Iogear USB Print Server GPSU01 Manual do Utilizador

USB Print ServerUser Manual (GPSU01)®

Installation and ConfigurationClick Next on the following window to proceedto the Component Selection window:7

At the Component selection window, make sureboth Network Print Monitor and PSAdmin arechecked. Click Next to proceed to start installingthese componen

This process may take a few minutes.Installation and Configuration9Click Finish on the following window when the aboveprocess is complete.

10Print Server Setup1. Select “Start” >> “Programs” >> “PSAdmin”Installation and Configuration

2. Your computer will search for the Print Server11Installation and Configuration3. Select your Print Server and double click on it.

4. You will now view the Print Server Properties.The “General” section allows you to view the nameof your Print Server and assign/change thepassword

5. Clicking the “TCP/IP” button in the Generalwindow allows you to view the IP address of yourPrint Server. You can either obtain a dynamic IPaddres

Note: If you don’t know the gateway address, you can contact the network administrator, or use thefollowing procedure to find the Gateway address: cli

6. “Netware,” “AppleTalk,” “SNMP” and “Advanced”are other protocols in which you may configure yourPrint Server. Clicking these buttons at the Config

Setup Procedure for Windows 2000/XP1. If you are adding a new printer, or just allowingmore computers to share a printer, you will have toinstall the

Follow the “Add Printer Wizard.”17Installation and Configuration

2. Select Local Printer. Make sure that the box:“Automatically detect and install my Plug and Playprinter” is unchecked.18Installation and Configura

3. Check “Create a new port,” and select“Network Print Port,” and click Next,19Installation and Configuration

4. Select your Print Server. If there are two printservers in your network, confirm their IP addresses.If the IP address is incorrect, type in the co

5. Select the printer. Click “Have Disk” if you havean installation disk, or download the driver onto yourcomputer.21Installation and Configuration

Select the corresponding drive where the driver islocated, or “Browse” for the driver. Click OK whenthe driver location is confirmed.22Installation an

6. Click Next to proceed with the Add Printer Wizard.23Installation and Configuration

7. Type the name of the printer or use default nameprovided by the printer manufacturer. If you have onlyone printer on the network, you should selec

8. Since the printer is connected to the networkdirectly, not through any particular computer, select“Do not share this printer” in the following wind

You can either select Yes or No on printing a testpage in the following window, and then click Next.26Installation and Configuration

Thank you for purchasing this 1-port USB Print Server that allows any networked computer to share a USBprinter. It complies with USB 1.1 specification

The installation of the driver is completed. ClickFinish in the following window.27Setup Procedure for Windows 98SE/ME:1.Follow the same steps that ar

Installation and ConfigurationInstall your printer per the instructions from the manufacturer with the printer connected directly to your computer.Onc

Printer Configuration for Mac OSNOTE: The USB print server ONLY supports post-script printers under Mac OS 8.6 or higher which aresupported by LaserW

3. Change Directory Service to AppleTalk andmake sure that the AppleTalk Network is set toLocal AppleTalk Zone.4. Select the available Print Server

5. A list of post-script printers will appear. Selectthe appropriate printer and click on Add.6. The necessary files will be installed. Theprocess

Setting up print server remotelyTelnet AccessYou can obtain access to the Print Server menu by using telnet:1. Select “Start” >> “Run”2. In the

4. Now you should be able to view the following screen and make your selections. The stepsof setting up is similar to the steps of setting it up loca

2. You should be able to view the following screenand make your selections. The set up step is similarthe steps to set up the print server locally.34

IPX/SPX: Internetwork Packet Exchange (IPX) is a networking protocol used by the Novell NetWare operatingsystems. It is a datagram protocol used for

Technical Support36If you need technical support, please check out our IOGEAR Tech Info Library (T.I.L.) atwww.iogear.com/support for the latest tips,

Table of ContentsPackage Contents...

IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT, INDIRECT,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OFTHE PRODUCT

23 Hubble • Irvine, CA 92618 • (P) 949.453.8782 • (F) 949.453.8785 • www.iogear.comContact info.®

GPSU01 Product Manual Addendum Rev. 01 Setup Procedure for Windows 98/ME/2000/XP NOTE: Under Windows 98/ME, you must initially install your Printer

3. A list of installed network adapters and protocols will be listed. If you wish to add a specific one, click Add. 4. Select Protocol, then click

This package contains: (1) Print Server (1) External AC Power Adapter (1) Driver CD (1) User Manual (1) Warranty Registration Card

• Easily connects your USB printer to a network• Allows multiple computers to share one USB printer on the network• Print from any computer on your ne

System RequirementsThis USB print server supports:• Windows 98SE/ME/NT/2000/XP• Novell(iBindery/NDS)• Mac OS 8.6 or Later• Unix/Linux• Printer with US

Software Installation1. Turn off the printer power.2. Install protocol in Windows 2000/XP (if necessay)Note: Although multiple protocols can be ins

Installation and Configuration6The procedure is as follows:Select Control Panel >> Network and Dial-upConnections >> Local Area Connection